November 20, 2018
  • 10:44 am 10 Ways To Fool The Authorities And Escape Martial Law- A Violent And Horrifying Life In A Concentration Camp Is What You May Face One Day Under Martial Law
  • 7:11 pm Raid Routes
  • 2:26 pm Situational Awareness: The Ability To Respond Quickly And Affirmatively (Is One The Most Important Skills You Can Learn to Master)
  • 12:51 pm 5 Devious Strategies That Will Get Preppers Killed: We Can Plan For Many Things But Nothing Is A Guarantee
  • 1:29 pm Scare Them Off Or Shoot Them Dead?

We’ve seen it a million times in movies and TV shows: a guy breaks into any old car, ties a few wires together below the steering wheel and, bam, drives off without any issues. Unfortunately, that’s Hollywood Hot-wiring. Real life hot-wiring is a little different, so before we begin there’s a few important things to keep in mind.

The reason for hot-wiring is simple; to allow you to start a car without the need for a key. There are a few occasions when you might need to legitimately do this to your own car; maybe you’ve lost your keys or your lock tumbler has jammed. It’s important to remember that hot-wiring any car that doesn’t belong to you is highly illegal (even though that likely wouldn’t be a concern in a SHTF scenario).

Secondly, there are several methods to hot-wiring cars, but the one we’re going to focus on is the one which requires the least tools. We’re going to keep things as minimal as possible. It’s not possible to do this entire process with your hands alone, although it is achievable with just a knife and providing you’re also built like Rambo. The tools you’ll ideally need are: pliers, knife, screwdriver, strength.Also, here are the tools you will need when SHTF.

Lastly, you may have heard people mention that it’s impossible to hot-wire a car newer than around the mid-nineties. This isn’t strictly true. Cars up until around 1999 can be hot-wired with the standard method which is outlined below. After this, it doesn’t get impossible, just more difficult and will require knowledge specific to certain vehicle makes and models.

It is true that cars newer than around 2004 are largely impossible to hot-wire. Modern vehicles come with a chip in their key fobs which are required for the ignition to start at all – no amount of hot-wiring can bypass these. There are a multitude of other ways to commandeer such vehicles, but all require either technological hacks through the use of smartphones or laptops, or just straight up stealing the keys.

But for now, let’s go back to basics.

We must understand what’s happening when we put a key in our ignition and turn it. With each turn, switches are being closed. Turning the key three times connects the three components needed to start a car: the battery, the ignition and the starter motor. Hot-wiring connects these three things without the need for a key.

So where are these wires located?

Step 1: Remove The Plastic CoveringP1 Hotwire Car

This POV is from underneath the dash. This is where you need to start. See that little screw there? That’s connecting the plastic cover which conceals all of the wires below the steering column. This is what you first need to remove. Depending on your car, there can be up to four of those screws, and you’ll need a Phillips-head screwdriver to take them out. Alternatively, you can brute force your way through without a screwdriver, however will render you unable to repair the column if that’s your intention.

Step 2: Locate The Correct Wires

You will then be greeted with an overwhelming amount of wires. Don’t worry though, because it’s easy to work out what they’re for by looking in the direction they’re going.P2 Hotwire Car

You should be able to make out three separate bundles of wires; one going to the left, one going to the right and one going straight into the steering column itself. It’s the steering column bundle we need.

The bundle you need will be taped or attached together with either industrial tape a clip of some kind. There should be five wires in total in the bundle and they will all be connected to the ignition cylinder (the piece of metal you would normally put your key into).

Step 3: Prep The Wires

The easiest way to do the next part, in my experience, is to isolate that whole section. Pull out wires along with the ignition cylinder so that you can manipulate the wires more easily. For ease of instruction, this is how the one I removed from the above vehicle looks like:P3 Hotwire Car

P4 Hot-wire CarNow, in a survivalist situation, you probably won’t have chance to check the car’s manual in order to determine which wire is which, so it would be useful to practice this step beforehand. The next stage is to locate the three wires required to start the vehicle: battery, ignition and starter.

The colors of these wires will vary depending on the make and model of the car. In my example, the wires I needed were blue, white and green, however, these were specific to my chosen vehicle. In general, red wires often indicate the battery and ignition wires, and started wires are usually brown/yellow. You can negate this issue, however, by pulling out the ignition cylinder with the wires. It will be the first three wires in the sequence which you need.P5 Hotwire Car

Step 4: Connect The Wires

Cut these three wires loose from the ignition cylinder and fray the protective rubber so you can expose the raw wire. Be very careful at this point. Do not touch the exposed wires with your bare hands.P6 Hotwire CarP7 Hotwire CarYou first need to attach the ignition wire and the battery wire to ‘light up’ the ignition (the same state the car is in when you turn your key twice; when you’re able to access your stereo but not able to drive). To do this, wrap the wires together and make sure they don’t come apart. Use protective gloves throughout (or a piece of clothing or cloth in a survival scenario). The dashboard should light up.P8 Hotwire Car

Then, hold the starter wire against the two battery wires until the engine kicks in. This will only take a second at most (imagine turning the ignition on with your key).P9 Hotwire Car

Immediately move the starter wire away and make sure it won’t come into contact with the battery wires while you’re driving. If necessary, use industrial tape around the edges of the wires to protect both yourself and the vehicle.

And we’re done. Rev the engine until it sounds healthy. The only thing to do in order to drive the vehicle normally is crack the steering lock, although this isn’t difficult. The lock can be broken by forcefully turning the wheel harshly in one direction until the lock-pins holding the wheel in place breaks.

So, the car is running, the steering wheel is free; what next? Well, it depends on your intentions. If you want to use the car again under normal circumstances then you will need some significant repair work done to the ignition cylinder, the battery wiring, the steering wheel lock and steering column.

If you’re planning on using the car regularly in its current iteration, you simply disconnect the two battery wires from touching each other in order to turn off the ignition. To restart it, re-attach the battery wires, then use the starter wire to fire it up.

Please follow and like us:
0
Harper

RELATED ARTICLES
LEAVE A COMMENT